background image

Harman®  •  Accentra 52i Installation Manual_R16  •  2013 -___  •  09/15

15

3-90-00574i

Harman® strongly recommends installing battery back-

up to minimize entry of smoke into the room in the 

event of power loss.

Your  pellet/biomass  burning  appliance  relies  on  a 

combustion blower to remove exhaust. A power failure will 

cause  the  combustion  blower  to  stop.  This  may  lead  to 

exhaust seeping into the room. Vertical rise in the venting 

may  provide  natural  draft.  It  is,  however,  no  guarantee 

against leakage.

There are two Harman® approved battery back-up 

options for your appliance:
Uninterruptible Power Supply (UPS) UPS

  battery 

back-ups  are  available  online  or  at  computer  and  office 

equipment stores. Your Harman® appliance with Rev E or 

later software available beginning in November 2010 may 

be plugged directly into a Harman® approved UPS:
•   The APC (American Power Conversion) model #BE750G 

and  the  TrippLite  model  INTERNET750U  are  tested 

and  approved.  Other  brands  or  models  may  not  be 

compatible.

When power is lost, a fully charged UPS will power a safe, 

combustion  blower  only  shut-down.  Your  appliance  will 

pulse the blower every few seconds to clear exhaust until 

the fire is out.

NOTE: The UPS provides safe shut-down only. It is not 

intended for continued operation.

Your appliance will recognize when power is restored. What 

happens  depends  on  ESP  temperature  and  whether  it  is 

equipped with automatic ignition:

• 

In “Automatic” setting,

 units equipped with automatic 

ignition will respond to the set point and ESP temperature 

and resume normal operation.

• 

In “Manual” setting

  or  for  units  without  automatic 

ignition:

•  If the ESP is cool, the appliance will remain shut down.
•  If the fire is out and the ESP is still warm, the feeder may 

restart. Since the fire is out, the ESP temperature will not 

rise. The unit will then shut-down, and may flash a six-

blink status error. (See ESP error codes)

•  If the fire is still burning, it will resume normal operation.
Contact  your  dealer  if  you  have  questions  about  UPS 

compatibility with your appliance.

Harman®  Surefire  512H  Battery  Back-up

  The  512H 

connects to a 12 volt deep cycle battery that will run your 

appliance  for  up  to  eight  (8)  hours.  It  includes  a  trickle 

charge feature that keeps your battery charged when power 

is available. 

NOTE: If the power is out for longer than 

battery life, smoke leakage may still occur unless your 

stove has been safely shut down.

Minimizing Smoke During Loss of Power Using Battery Back-up

CAUTION

!

Always keep appliance doors and hopper lid closed 

and latched during operation and during power 

failures to minimize risk of smoke or burn-back.

CAUTION

!

Use only Harman® approved battery back-up devices. 

Other products may not operate properly, can create 

unsafe conditions or damage your appliance.

Summary of Contents for Accentra 52i Pellet Insert































Reviews: