23
OPERATION
Operation
• Press and briefly hold the
Memory/
Program
button
w
and release it when the
MEMORY
J
and
PRESET
I
indicators
begin to flash.
• Within three seconds, press the
CLEAR
button
v
and hold it until the
Main
Information Display
N
reads
CLEAR
.
This will be followed by the preset memory
number being cleared.
• The tuner will then return to normal
operation.
• The preset memory number that was cleared
is then “empty” and may be left alone or
assigned to another station.
Tape Recording
In normal operation, the audio or video source
selected for listening through the AVR 100 is
sent to the record outputs. This means that any
program you are watching or listening to may
be recorded simply by placing machines con-
nected to the outputs for
Tape Out
i
or
Video 1
°
in the record mode.
NOTE:
Please make certain that you are aware
of any copyright restrictions on any material
you copy. Unauthorized duplication of copy-
righted materials is prohibited by Federal law.
Output-Level Trim Adjustment
Normal output-level adjustment for the
AVR 100 is established using the Test Tone, as
outlined on page 17. In some cases, however, it
may be desirable to adjust the output levels
using program material such as a test disc, or a
selection you are familiar with. Additionally, the
output level for the subwoofer can only be
adjusted using this procedure.
To adjust the output levels using program
material, first set the reference volume for the
front-left and front-right channels using the
Volume Control
ˆ
. If you wish to vary
the difference between the left and right chan-
nels, use the
Balance Control
7
.
Once the reference level has been set, press
the
Channel-Select
button
q 32
and note
that
FRONT L LEV
will appear in the
Main Information Display
N
. To change
the level, first press the
Set
button
t 31
,
and then use the
Selector
buttons
34
or the
‹
/
›
buttons
r
to raise or lower the level.
DO NOT use the volume control, as this will
alter the reference setting.
Once the change has been made, press the
Set
button
t 31
and then press the
Selector
buttons
34
or the
‹
/
›
buttons
r
to select
the next output channel location that you wish
to adjust. To adjust the subwoofer level, press
the
Selector
buttons
34
or the
‹
/
›
buttons
r
until
S-WOOFER LEV
appears in the
Main Information Display
N
.
Press the
Set
button
t 31
when the name
of the desired channel appears in the
Main
Information Display
N
, and follow the
instructions shown earlier to adjust the level.
Repeat the procedure as needed until all chan-
nels requiring adjustment have been set. When
all adjustments have been made and no further
adjustments are made for twenty seconds, the
AVR 100 will return to normal operation.
NOTE:
The output levels may be separately
trimmed for each digital and analog surround
mode. If you wish to have different trim levels for
a specific mode, select that mode using the front-
panel buttons
Ó Ô Ò Ú
or
on the
remote control and follow the instructions in the
steps shown above.
6-Channel Direct Input
The AVR 100 is equipped for future expansion
through the use of optional, external adapters
for formats that the AVR 100 may not be capa-
ble of processing. When an adapter is connected
to the
6-Channel Direct Input
·
, you may
select it by pressing the
6-Ch Input Selector
$
.
Note that when the 6-Channel Direct Input is in
use, you may not select a surround mode, as
the external decoder determines processing. In
addition, there is no signal at the record out-
puts when the 6-Channel Direct Input is in use.
Memory Backup
This product is equipped with a memory backup
system that preserves tuner presets and system
configuration information if the unit is acciden-
tally unplugged or subjected to a power out-
age. This memory will last for approximately
two weeks, after which time all information
must be reentered.
36
33
31
