background image

 - 

 

 

HARISON INDUSTRIAL DEHUMIDIFIER - USER'S MANUAL -  Model: HD-100BM 

 
Warning : 

 
The use life will be prolonged if checking, maintaining periodically. Please send 
professional person to damage. 

 
6. TROUBLES AND COUNTERMEASURES 
 
Phenomenon 

analysis of causes 

Countermeasures 

Machine does not run. 

Power failure 
Power source is not 
switched on not well 
plugged  
Fuse is broken 

 
Switch on the power source 
plug in 
Replace the fuse after 
removing troubles 

Machine can not dehumidify 
or the effect is bad. 

Air filter dusted 
 
Air inlet and outlet 
obstructed door or window 
is open 
 
Refrigerant leakage 

Clean the air filter 
 
Remove the obstacle 
Close the door and the 
window, shade the sun with 
curtains, etc. 
Contact dealer and repair it 

Water leakage 

Machine inclined backward 
Drain pipe is blocked 

Level the unit 
Remove the front panel and 
wipe off dirt from the pipe 

"POWER/PROTECTION" 
light flashes. 

The temperature sensor is 
open circuit or short circuit. 

Replace the temperature 
sensor 

Machine can not defrost 

The  temperature  sensor  is 
loosening. 
 
The valve is damaged. 

Fix the temperature sensor 
well 
 
Replace the valve 

If the troubles have not been removed yet, please contact the dealer. 
 
When the dehumidifier is starting or stopping, the sound of the cycling of refrigerant 
does not mean a trouble. 
 
It is normal that hot wind is discharged the air outlet. 
 
Notice 
Please switch off the power source after stopping. 
Must be grounded reliably when installing. 
Please keep this manual in a suitable storage for reference. 
 
 

PLEASE CONTACT YOUR NEAREST HARISON SUPPLIER FOR ANY 

TECHNICAL ASSISTANCE ! 

Summary of Contents for HD-100BM












Reviews: