manualshive.com logo in svg

Hardi NAVIGATOR 3000, Operator'S Manual, Page: 63 / 122

Share
Download
Hardi NAVIGATOR 3000 Operator'S Manual Download Page 63

5 - Operation

61

Filling of main tank using Quick fill

The Quick Filling Device is operated as follows:

1.

Turn Suction SmartValve to unused function (closed).

2.

Remove cap from Quick Fill valve and connect filling hose from 
water supply.

3.

Turn handle on Quick Fill valve towards indicator (up).

4.

Keep an eye on the main tank level indicator in order not to overfill 
the tank.

5.

Close the Quick Fill valve (horizontal) and remove the filling hose.

6.

Replace the cap on the Quick Fill coupler when filling is complete.

˜

ATTENTION! Observe local legislation regarding use of filling 
device. In some areas it is prohibited to fill from open water 
reservoirs (lakes, rivers etc.). It is recommended only to fill from 
closed reservoirs (mobile water tanks etc.) to avoid 
contamination.

±

WARNING! Do not leave the sprayer while filling the tank. Keep an eye on the level indicator in order NOT to overfill 
the tank.

±

WARNING! If filling hose/filter is carried on the sprayer during spraying, it can be contaminated by spray drift which 
will be transferred to water source when filling! 

Filling of Rinse Tank using Quick fill

A rinse tank is integrated into the rear of the sprayer and is filled via the 
rinse tank quick coupler located near the SmartValves.

1.

Remove cap from Quick Fill coupler and connect filling hose from 
water supply.

2.

Fill rinse tank to desired level.

3.

Keep an eye on the rinse tank level indicator located on the 
platform behind the main tank level indicator.

4.

Stop filling and remove the filling hose.

5.

Replace the cap on the Quick Fill coupler when filling is complete.

Volume: approximately 130 gal. (500 liters).

˜

ATTENTION! Only fill rinse tank with clean water! To avoid algae 
developing in the rinse tank, always drain this tank if the sprayer 
is not in use for a long period of time.

˜

ATTENTION! For cleaning purposes etc., the rinse tank is also accessible via the tank lid on top of the tank.

˜

ATTENTION! Observe local legislation regarding use of filling device. In some areas it is prohibited to fill from open 
water reservoirs (lakes, rivers etc.). It is recommended only to fill from closed reservoirs (mobile water tanks etc.) to 
avoid contamination.

±

WARNING! Do not leave the sprayer while filling the tank. Keep an eye on the level indicator in order NOT to overfill 
the tank.

±

WARNING! If filling hose/filter is carried on the sprayer during spraying, it can be contaminated by spray drift which 
will be transferred to water source when filling! 

Summary of Contents for NAVIGATOR 3000



























































































































Reviews:

No comments