manualshive.com logo in svg

Hardi ARROW 2000, Instruction Book

Share
Download
Hardi ARROW 2000 Instruction Book Download Page 49

5 - Operation

47

Filling liquid chemicals by HARDI TurboFiller (optional)

1.

Fill the main tank at least 1/3 with water (unless otherwise stated on 
the chemical container label).

2.

Turn the Manifold valve towards towards TurboFiller.

3.

Set the fan gear lever to neutral position, engage the pump and set 
P.T.O. at 540 r/min. 

4.

Open TurboFiller lid. Measure the correct quantity of chemical and 
fill it into the hopper.

5.

Engage the hopper transfer device by opening the TurboFiller suc- 
tion valve and the chemical is being transferred to the main tank.

Engage the flushing devise to flush the hopper. If powder chemicals are 
filled the flushing device must be open before pouring the powder into 
the hopper.

6.

If the chemical container is empty, it can be rinsed by the Chemical 
Container Cleaning device. Place the container over the multi-hole 
nozzle and push the upper lever to the left of the TurboFiller.

7.

Close TurboFiller suction valve when the hopper has been rinsed.

8.

Close the TurboFiller lid.

€

DANGER! Always wear face shield and other appropriate personal 
safety equipment when filling chemicals.

±

ATTENTION! The scale in the hopper can only be used if the sprayer is parked on level ground! It is recommended to 
use a measuring jug for best accuracy.

€

DANGER! In order to avoid spray liquid hitting the operator, do not press lever unless the multi-hole nozzle is covered 
by a container as spray liquid may otherwise hit the operator.

±

ATTENTION! Rinsing device uses spray liquid to rinse containers for concentrated chemicals. Always rinse the che- 
mical containers with clean water several times until they are clean before disposal.

±

ATTENTION! The hopper rinsing device is using spray liquid for rinsing the hopper for concentrated chemical! 
Cleaning the TurboFiller must always be done when the spray job is ended and together with the entire sprayer - a 
cleaning after the last filling and before spraying the last tankful does not ensure a clean TurboFiller!

9.

Disconnect the pressure to the TuboFiller, keep agitation activated to ensure homogene concentration. 

10.

Engage the fan gearbox before spraying.

Summary of Contents for ARROW 2000





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands