manualshive.com logo in svg

Hardi ARROW 2000, Instruction Book

Share
Download
Hardi ARROW 2000 Instruction Book Download Page 20

3 - Description

18

TurboDeflector valve

This TurboDeflector valve activates the Vortex flushing of the 
TurboFiller. Lift the lever to lock it in open position for continuous liquid 
rotation in the hopper.

Chemical Container Rinsing lever

The upper lever is used for two purposes:

When the TurboFiller lid is open: For rinsing empty containers. Place 
the container over the rotating flushing nozzle in the middle of the 
TurboFiller to rinse the inside of the container.

When the TurboFiller lid is closed: Use the Chemical Container Rinsing 
lever to rinse the hopper when the filling of chemicals is completed.

€

DANGER! Do not press the lever unless the multi-hole nozzle is covered by a container as spray liquid may otherwise 
hit the operator.

Rinse tank

The rinse tank is coaxially coupled inside the 2000, 3000 and 3800 litre 
tanks. 

This tank is completely separate and is not connected with the main 
tank. 

±

WARNING! The tank should only be filled with clean water and a 
disinfectant agent, and it should only be used for rinsing and 
cleaning the equipment inside and out. 

Start TurboDeflector

Chemical Container Rinsing

Summary of Contents for ARROW 2000





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands