background image

Page 3

For technical questions, please call 1-800-444-3353.

SKU 02628 

        

 

its intended function. Check for alignment and binding of moving parts; any broken parts or 

mounting fixtures; and any other condition that may affect proper operation. Any part that 

is damaged should be properly repaired or replaced by a qualified technician. 

11. 

Replacement parts and accessories

.  When servicing, use only identical replacement 

parts. Use of any other parts will void the warranty. Only use accessories intended for use 

with this movable bicycle rack. Approved accessories are available from Harbor Freight 

Tools.

12. 

Do not assemble Cycle Tree if under the influence of alcohol or drugs

.  Read warning 

labels on prescriptions to determine if your judgment or reflexes are impaired while taking 

drugs. If there is any doubt, do not assemble the Cycle Tree .

13. 

Maintenance

.  For your safety, parts replacement or repair should be performed by a 

qualified technician.

14. 

Maintain Balance

.  To obtain the best and safest performance of the Cycle Tree, be sure 

that the multiple hanging bicycles are evenly distributed on the Cycle Tree.   

Be careful to follow the operation instructions.

Warning: The warnings, cautions, and instructions discussed in this instruction manual 

cannot cover all possible conditions and situations that may occur. It must be understood 

by the operator that common sense and caution are factors which cannot be built into this 

product, but must be supplied by the operator.

Unpacking

When unpacking, check to make sure all the parts listed on page 7 are included. If any parts are 

missing or damaged, please call Harbor Freight Tools at the number on the cover of this manual 
as soon as possible.

REV 03l, 06l, 09k, 10l, 11a

Summary of Contents for 02628








Reviews: