background image

-  29  -

ⓐ  Examination  method

      -  Operate  the  outrigger  in  appropriate  location(  about  10  ㎜  locations  ,  ink  etc. 

used  in  load),  turn  off  the  engine  in  maximum  rise  state.

      -  After  marking  and  10  minutes  please  check  descend  status.    (2  ㎜  or  less           

          shrinkage  )

ⓑ  Caution

      -  Please  stop  the  operation  when  quickly  descend  during  operation  as  other 

cylinder  might  be  descend  at  the  same  time.

      -  If  problem  exists,  please  contact  the  company  and  the  A/S. 

2)  Derrick  cylinder  normal  descent

-  When  operation,  derrick  cylinder  directly  link  to  safety  of  worker  and  beforehand 

please  do  maintenance  inspections.

ⓐ  Examination  method

    -  1/3  of  the  boom  is  out  and  1  step  boom  is  located  parallel  with  the  vehicle, 

the  tube  and  the  load  of  derrick  cylinder  crack,  mark  to  use  ink  etc. 

    -  After  marking  and  10  minutes  please  check  descend  status.    (2  ㎜  or  less             

        shrinkage  )

  ⓑ  Caution

    -  Please  fold  each  step  when  quickly  descend  during  operation,  1  step  boom           

        should  be  elevated.

    -  If  problem  exists,  please  contact  the  company  and  the  A/S.

3)  Extension  cylinder  normal  descent

  ⓐ  Examination  method

    -  50-60kg  objects  to  be  load  on  the  boarding  platform,  mark  the  appropriate 

location  of  each  stage  of  contraction  and  expansion  of  the  boom.  (  two  stages 

and  three  ,  three  stages  and  four  ) 

    -  After  marking  and  10  minutes  please  check  descend  status.    (3  ㎜  or  less             

        shrinkage  )

  ⓑ  Caution

    -  Please  stop  the  operation  when  quickly  descend  during  operation  and  operate     

        the  contraction  direction.

    -  If  problem  exists,  please  contact  the  company  and  the  A/S.

Summary of Contents for HS Series

































Reviews: