Hanna Instruments HI98198 OPDO Instruction Manual Download | Manualshive

Page: 57 / 60

background image

57

57

W

ARRANTY

FCC Rules, Section 15.105
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radi-
ate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/ TV technician for help.

WARRANTY

HI98198 i

s warranted for two years against defects in workmanship and materials when used for its

intended purpose and maintained according to instructions. Electrodes and probes are warranted for a
period of six months. This warranty is limited to repair or replacement free of charge. Damage due to
accidents, misuse, tampering or lack of prescribed maintenance is not covered.
If service is required, contact your local Hanna Instruments Office. If under warranty, report the model
number, date of purchase, serial number (see engraved on the back of the instrument) and the nature
of the problem. If the repair is not covered by the warranty, you will be notified of the charges incurred.
If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization
number from the Technical Service department and then send it with shipping costs prepaid. When
shipping any instrument, make sure it is properly packed for complete protection.

«
...
55
56
57
58
59
...
»

Summary of Contents for HI98198 OPDO





























































Reviews:

No comments

Related manuals for HI98198 OPDO

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 63

Brand: Igema Pages: 30

Brand: z-laser Pages: 62

Brand: Van Walt Pages: 2

Brand: OHAUS Pages: 26

Brand: Make Noise Pages: 15

Brand: Major tech Pages: 40

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 60

GranTouch Digital Grand Piano

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands