background image

19

18

4.2 SENSOR PREPARATION / ACTIVATION

4.2.1 pH Preparation

Remove the shipping cap from the pH sensor. If the shipping cap does not contain
any liquid, pour 

HI 70300

 into shipping cap, place it back on the sensor and

soak for at least 1/2 hour before use. If 

HI 70300

 is not available, pH 4.01

buffer may be substituted.

4.2.2 ORP Activation

For improved redox measurements, the surface of the sensor must be clean and
smooth. A pretreatment procedure should be performed to ensure quick response.
The pretreatment of the sensor is determined by the pH and the ORP potential
values of the sample. Use the table below to determine the treatment required.
First locate the typical sample pH. If the corresponding ORP value (mV) is higher
than the values in the table below, an oxidizing pretreatment is necessary. If the
value is lower, a reducing pretreatment is necessary.

pH

mV

pH

mV

pH

mV

pH

mV

 pH

 mV

0

990

 1

920

 2

860

 3

800

 4

 740

5

680

6

640

 7

580

 8

520

 9

 460

10 400

 11

340

12

280

 13

220

 14

 160

For reducing pretreatment: immerse the electrode for at least five minutes in

HI 7091

.

For oxidizing pretreatment: immerse the electrode for at least five minutes in

HI 7092

.

Chapter 4 - PROBE INSTALLATION

4.1 SENSOR DESCRIPTIONS

HI 769828-0

     Combination pH sensor features a glass pH

sensitive bulb and a silver/silver chloride double junction
reference with gelled electrolyte.

HI 769828-1

     Combination pH/ORP sensor features a glass

sensitive bulb for pH readings, a platinum sensor for redox
measurements and a silver/silver chloride double junction
reference with gelled electrolyte.

Note

See section 4.2.1 for pH preparation.
See section 4.2.2 for ORP activation.

HI 769828-2

 Galvanic dissolved oxygen (D.O.) sensor. The

thin gas permeable membrane isolates the sensor elements
from the testing solution but allows oxygen to pass through.
The oxygen that passes through the membrane is reduced
at the cathode and causes a current, from which the oxygen
concentration is determined. The D.O. sensor conforms to
Standard Methods 4500-AG, EPA 360.1.

Note

The D.O. sensor needs to be activated before instal-
lation. See section 4.2.3 for details.

HI 769828-3

 4 ring-electrode conductivity (EC/TDS/Resistivity/

Salinity) sensor. The sensor is immune to polarization or surface
coatings.

Summary of Contents for HI98194






































Reviews: