manualshive.com logo in svg

Hanna Instruments Groline HI981412, Instruction Manual

Share
Download
Hanna Instruments Groline HI981412 Instruction Manual Download Page 29

29

EVENTS MANAGEMENT

9.  EVENTS MANAGEMENT

9.1.  ALARMS

Alarms can be independently enabled or disabled in SETUP.
Any event that activates the alarm turns automatic control Off, the alarm relay is deactivated and the 
LCD backlight is blinking red. 
The table below illustrates the conditions that will activate the alarm and deactivate the control pump.

Alarm

Description

Alarm condition

Solution

Overtime 
alarm

Pump remains on 
continuously for the 
time set in menu 
Overtime Alarm setting

Control is switched off.
Pump is activated in 
Manual mode.

Hold level 
alarm

Low-level sensor 
active

Refill chemical reagent 
container. 

Low alarm

Measured pH is lower 
than the Low Alarm 
threshold value, for 
more than 5 seconds

Increase pH content of 
process to acceptable 
values.

High alarm

Measured pH is 
higher than set 
threshold alarm High 
pH, for more than 
5 seconds

Decrease process pH 
content to acceptable 
values.

Summary of Contents for Groline HI981412













































Reviews:

No comments

Brands by name

Popular brands

Load more brands