background image

61

Hangar 9 Jackal 50 ARF

2010 Official Academy of Model 

Aeronautics Safety Code

GENERAL

1.   A model aircraft shall be defined as a non-human-

carrying device capable of sustained flight in the 

atmosphere. It shall not exceed limitations established 

in this code and is intended to be used exclusively for 

recreational or competition activity.

2.   The maximum takeoff weight of a model aircraft, 

including fuel, is 55 pounds, except for those flown 

under the AMA Experimental Aircraft Rules.

3.   I will abide by this Safety Code and all rules established 

for the flying site I use. I will not willfully fly my model 

aircraft in a reckless and/or dangerous manner.

4.   I will not fly my model aircraft in sanctioned events, 

air shows, or model demonstrations until it has been 

proven airworthy.

5.   I will not fly my model aircraft higher than approximately 

400 feet above ground level, when within three (3) miles 

of an airport without notifying the airport operator. I will 

yield the right-of-way and avoid flying in the proximity of 

full-scale aircraft, utilizing a spotter when appropriate.

6.   I will not fly my model aircraft unless it is identified with 

my name and address, or AMA number, inside or affixed 

to the outside of the model aircraft. This does not apply 

to model aircraft flown indoors.

7.   I will not operate model aircraft with metal-blade 

propellers or with gaseous boosts (other than air), 

nor will I operate model aircraft with fuels containing 

tetranitromethane or hydrazine.

8.   I will not operate model aircraft carrying pyrotechnic 

devices which explode burn, or propel a projectile of 

any kind. Exceptions include Free Flight fuses or devices 

that burn producing smoke and are securely attached 

to the model aircraft during flight. Rocket motors up 

to a G-series size may be used, provided they remain 

firmly attached to the model aircraft during flight. Model 

rockets may be flown in accordance with the National 

Model Rocketry Safety Code; however, they may not be 

launched from model aircraft. Officially designated AMA 

Air Show Teams (AST) are authorized to use devices 

and practices as defined within the Air Show Advisory 

Committee Document.

9.   I will not operate my model aircraft while under the 

influence of alcohol or within eight (8) hours of having 

consumed alcohol.

10.   I will not operate my model aircraft while using any drug 

which could adversely affect my ability to safely control 

my model aircraft.

11.   Children under six (6) years old are only allowed on a 

flightline or in a flight area as a pilot or while under flight 

instruction.

12.   When and where required by rule, helmets must be 

properly worn and fastened. They must be OSHA, DOT, 

ANSI, SNELL or NOCSAE approved or comply with 

comparable standards.

RADIO CONTROL

1.   All model flying shall be conducted in a manner to avoid 

over flight of unprotected people.

2.   I will have completed a successful radio equipment 

ground-range check before the first flight of a new or 

repaired model aircraft.

3.   I will not fly my model aircraft in the presence of 

spectators until I become a proficient flier, unless I am 

assisted by an experienced pilot.

4.   At all flying sites a line must be established, in front of 

which all flying takes place. Only personnel associated 

with flying the model aircraft are allowed at or in front of 

the line. In the case of airshows demonstrations straight 

line must be established. An area away from the line 

must be maintained for spectators. Intentional flying 

behind the line is prohibited.

5.   I will operate my model aircraft using only radio-

control frequencies currently allowed by the Federal 

Communications Commission (FCC). Only individuals 

properly licensed by the FCC are authorized to operate 

equipment on Amateur Band frequencies.

6.   I will not knowingly operate my model aircraft within 

three (3) miles of any preexisting flying site without 

a frequency-management agreement. A frequency 

management agreement may be an allocation of 

frequencies for each site, a day-use agreement between 

sites, or testing which determines that no interference 

exists. A frequency-management agreement may exist 

between two or more AMA chartered clubs, AMA 

clubs and individual AMA members, or individual 

AMA members. Frequency-management agreements, 

including an interference test report if the agreement 

indicates no interference exists, will be signed by all 

parties and copies provided to AMA Headquarters.

7.   With the exception of events flown under official AMA 

rules, no powered model may be flown outdoors closer 

than 25 feet to any individual, except for the pilot and 

located at the flightline.

8.   Under no circumstances may a pilot or other person 

touch a model aircraft in flight while it is still under 

power, except to divert it from striking an individual.

9.   Radio-controlled night flying is limited to low-

performance model aircraft (less than 100 mph). The 

model aircraft must be equipped with a lighting system 

which clearly defines the aircraft’s attitude and direction 

at all times.

10.   The operator of a radio-controlled model aircraft shall 

control it during the entire flight, maintaining visual 

contact without enhancement other than by corrective 

lenses that are prescribed for the pilot. No model aircraft 

shall be equipped with devices which allow it to be flown 

to a selected location which is beyond the visual range 

of the pilot.

Summary of Contents for Jackal 50 ARF

































































Reviews: