manualshive.com logo in svg

Hand Held Products Quick Check 200 Series, User Manual

Share
Download
Hand Held Products Quick Check 200 Series User Manual Download Page 7

 

1 

1. About This Manual 

This manual contains information on the Quick Check

®

 200 Series.  

•

  Quick Start Command Code 

•

 Detailed Operation 

•

  Configuration / Programming  

•

  Symbol Testing / Scan Results 

•

 Printer Printouts 

•

 Special Functions 

•

  Quick Check Maintenance 

•

  Single Scan to Result (SSTR) 

Conventions 

This manual uses several special symbols to refer to the controls on the 
instrument.  The following table shows the symbols and their descriptions. 

 

Symbol Description 

POWER or Scroll  [<>] or 

Select

 

Represents a button on the Quick Check 
unit

 

-Specs- or OK-to-Scan

 

Shows the LED display on the Quick 
Check unit

 

           ♦

 

Indicates steps to follow to perform a 
procedure

 

QC200 “Low Battery” Warning 

The Quick Check

®

 200 Series dynamically checks the condition of its battery 

when turned on and during menu cycles.  If any test falls below a specified limit, 
the LCD will show “Low Battery” (and the unit “beeps” five times) as a warning 
that the battery’s charge may be deteriorating.  The QC200’s microprocessor 
“sets” a system “flag” or “pointer” that indicates a degraded condition was 
measured for that particular test.  With this “flag” set, further cycling of the menu 

Summary of Contents for Quick Check 200 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands