manualshive.com logo in svg

Hand Held Products Quick Check 200 Series, User Manual

Share
Download
Hand Held Products Quick Check 200 Series User Manual Download Page 27

 

21 

5.  Symbol Testing & Scan Results 

The Quick Check

®

 200 Series acquires data during a measurement scan utilizing 

the new software-intensive “ScanProfile” methodology as specified in ANSI’s 
“Bar Code Print Quality Guideline” (ANSI x3.182).   (NOTE:  In all cases, the 
more smooth and slow the scan, the more accurate the results.)  the user may be 
prompted with a series of beeps (one long and three short) and one of the 
following displays: 

[Scan Slower!]  or  [Scan Evenly!]  or  [Scan Faster!] 

indicating that the scan was either too fast, too uneven/erratic or too slow for 
proper data collection.  A practiced, more deliberate and smooth rescan should 
be made to insure accurate results. 

Both pass/fail testing and detailed measurements on a given symbol are 
obtained simply by scanning across it with the QC200.  The most accurate 
results will be obtained by starting just outside the quiet zone and scanning in a 
single, smooth motion with the optics tips and reflectance guide “foot” lightly 
touching the symbol surface.  Practice helps!  A successful measurement will be 
signaled by beeping, a blinking green (pass) or red (fail) LED and the display 
showing results such as: 

 

Summary of Contents for Quick Check 200 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands