Hamworthy Sherborne Series, Installation, Commissioning And Servicing Instructions

Page: 15 / 54

HAMWORTHY HEATING LTD
13
SHERBORNE 500001167/E
5.8.3 Connection of Twin Pipe Horizontal/Vertical Room Sealed –100mm
Note: the flue support cradle is not required for this installation & should be discarded.
•
Secure the flue elbow mounting bracket to the wall frame using 3xM6
nuts & washers.
•
Locate the two elbows in the mounting bracket lugs & fit appliance
connector duct between flue outlet on the boiler discharge support
elbow.
•
Insert the inlet support elbow into the air inlet box.
•
Insert the 80-100mm adaptors into the elbow outlets.
•
Fit remaining flue components on route to terminal discharge ensuring
a minimum 2° slope & the flue system is self supporting using wall
brackets where necessary.
•
When terminating the system, ensure the joint through the wall / roof is
made good & weatherproofed. Whilst carrying out the above procedure
ensure that all seals are correctly located & provide gas tight joints.
•
The top of the plastic boiler cover has a D shaped recess for the
vertical flue exit point. Using a suitable fine toothed hacksaw or jigsaw,
cut around the inside of the recess to provide the flue outlet.
5.8.4 Connection of Twin Pipe Horizontal/Vertical Room Sealed –100mm
Note: the flue support cradle is not required for this installation & should be discarded.
•
Secure the flue elbow mounting bracket to the wall frame using 3xM6
nuts & washers.
•
Locate the two elbows in the mounting bracket lugs & fit appliance
connector duct between flue outlet on the boiler discharge support
elbow.
•
Insert the inlet support elbow into the air inlet box.
•
Insert the 80-100mm adaptors into the outlets of the elbows.
•
Fit the remaining components on route to the terminal discharge
ensuring a minimum 2° slope & the flue system is self supporting
using wall brackets where necessary.
•
In terminating the flue ensure that the joint through the wall/roof is made
good & weatherproofed. Whilst carrying out the above procedure
ensure that all seals are correctly located & provide gas tight joints.
•
The top of the plastic boiler cover has a D shaped recess for the
vertical flue exit point. Using a suitable fine toothed hacksaw or jigsaw, cut around the inside of the recess
to provide the flue outlet.
5.8.5 Connection of Single Pipe Horizontal/Vertical Room Sealed –100mm
Note: the flue support cradle is not required for this installation & should be discarded.
•
Secure the flue elbow mounting bracket to the wall frame using
3xM6 nuts & washers.
•
Locate the two elbows in the mounting bracket lugs & fit appliance
connector duct between flue outlet on the boiler discharge support
elbow.
•
Insert the inlet support elbow into the air inlet box.
•
Insert the 80-100mm adaptors into the outlets of the elbows.
•
Fit the remaining components on route to the terminal discharge
ensuring a minimum 2° slope & the flue system is self supporting
using wall brackets where necessary.
•
In terminating the flue ensure that the joint through the wall/roof is made
good & weatherproofed. Whilst carrying out the above procedure
ensure that all seals are correctly located & provide gas tight joints.
•
The top of the plastic boiler cover has a D shaped recess for the vertical flue exit point. Using a suitable fine
toothed hacksaw or jigsaw, cut around the inside of the recess to provide the flue outlet.
90° support elbow
Flue elbow
Mounting bracket
Appliance connector
Air inlet box
Ø80/100 eccentric
adapter
Ø100/150 concentric
adapter
Air inlet
Flue elbow
90° support elbow
Mounting bracket
Appliance connector
ø80/100 eccentric
adapter
ø100 Flue
Air inlet box
terminal
Appliance connector
90° support elbow
Mounting bracket
Flue elbow
Air inlet box
ø80/100 eccentric
ø100 Flue
adapter