Hammer INSPIRE SCS Cage, Manual

Page: 19 / 32

18
Select a Lower Cable (with “U” Bracket). Lay it out assuring it is
not kinked. Attach the “U” Bracket to the Cable Anchor Plate
upper center hole. Route the cable up through the Floating
Pulley Assembly with Guide Bushing, then down around the rear
pulley position and into the Base Beam. Push the cable forward
through the Base Beam past the front pulley position. Route the
cable out through the smaller hole and up around the Lower
Cable Column Mount Pulley, capturing the cable between the
pulley and the lower cable retainer tab only. Install the front and
rear Pulleys assuring that the cable is seated in their grooves.
Route the cable up the Cable Column and between the Dual
Pulleys on the Cable Column Slider. To secure the Cable End,
place one Plastic Ball onto the end of the cable. Next slide the
cable end into the slot of the Cable End “U” Bracket. Finally,
attach the Spring Clip to the “U” Bracket using the M6 x 20
Button Head Bolt and M6 Flat Head Nut. Slide the retainer “O”
Ring tight against the Plastic Ball to complete it.
Vyberte spodn
í
kabel (s dr
žá
kem
„
U“). Polo
ž
te si jej a ujist ě te se,
ž
e nen
í
zalomen
ý
. P
ř
ipevn
ě
te
„
U“ dr
žá
k k horn
í
mu st
ř
edov
é
mu
otvoru v kotevn
í
desce kabelu. Ve
ď
te lanko nahoru skrz sestavu
plovouc
í
kladky s vodic
í
m pouzdrem, potom dol
ů
kolem polohy
zadn
í
kladky a do z
á
kladn
í
ho nosn
í
ku. Zatla
č
te lanko dop
ř
edu
skrz z
á
kladn
í
nosn
í
k za polohu p
ř
edn
í
kladky. Ve
ď
te kabel ven
men
ší
m otvorem a nahoru kolem spodn
í
kladky pro mont
áž
na
sloupek kabelu, p ř i č em
ž
kabel zachy ť te pouze mezi kladku a
spodn
í ú
chytku kabelu. Nainstalujte p ř edn
í
a zadn
í
kladku a ujis-
t ě te se,
ž
e lanko sed
í
ve sv
ý
ch dr
áž
k
á
ch. Ve ď te kabel nahoru po
sloupku kabelu a mezi dv ě ma kladkami na jezdci sloupu kabelu.
Pro zaji
š
t
ě
n
í
konce kabelu um
í
st
ě
te na konec kabelu jednu
plastovou kuli
č
ku. Pot
é
zasu
ň
te konec kabelu do
š
t
ě
rbiny
„
U“
dr
žá
ku konce kabelu. Nakonec p
ř
ipevn
ě
te pru
ž
inovou svorku k
„
U“ dr
žá
ku pomoc
í
M6 x 20
š
roubu s knofl
í
kovou hlavou a mati-
ce s plochou hlavou M6. Zasu
ň
te p
ří
dr
ž
n
ý „
O“ krou
ž
ek t
ě
sn
ě
k
plastov
é
kouli, abyste tento krok dokon
č
ili.
Plovoucí kladka s pr
ů-
chodkou
Šroub
Šroub
Šroub
Podložka
Matice
Vložka
Spodní abel
Plastová kuli
čka
U-otvor
Hák
Za
čátek
kabelu
Šroub
Matice
Šroub
Šroub
Kabel uvnit
ř tyče
Šroub
Vložka