background image

Document #101-0008

        16

         11/11/05

LIMITED WARRANTY AGREEMENT

OF HAMILTON MANUFACTURING CORP.

Hamilton Manufacturing Corp., an Ohio Corporation, (“Seller”) warrants to Purchaser that all new

equipment shall be free from defects in material and factory workmanship for a period of one (1) year from the
original shipping date. Hamilton Manufacturing Corp. further warrants if any part of said new equipment in
Seller’s sole opinion, requires replacement or repair due to a defect in material or factory workmanship during
said period, Seller will repair or replace said new equipment. Purchaser’s remedies and the liabilities and
obligations of Seller herein shall be limited to repair or replacement of the equipment as Seller may choose, and
Seller’s obligation to remedy such defects shall not exceed the Purchaser’s original cost for the equipment.
Purchaser EXPRESSLY AGREES this is the EXCLUSIVE REMEDY under this warranty. There are no other
express or implied warranties which extend beyond the face hereof. All warranty repair service must be
performed by either a Factory Trained Service Representative or 

HAMILTON MANUFACTURING

CORP., 1026 Hamilton Drive, Holland, Ohio 43528 PHONE (419) 867-4858 or (800) 837-5561, FAX
(419) 867-4867.

The limited warranty for new equipment is conditioned upon the following:

1.

The subject equipment has not, in the Seller’s sole opinion, been subjected
to: accident, abuse, misuse, vandalism, civil disobedience, riots, acts of
God, natural disaster, acts of war or terrorism.

2.

 The Seller shall not be liable for any expense incurred by Purchaser inci-
dental to the repair or replacement of equipment and Purchaser shall
assume full responsibility for any freight or shipping charges.

3.

The coverage of this warranty shall not extend to expendable parts.

4.

 Purchaser shall have a warranty registration card on file with Seller prior to
any claim in order for warranty protection to apply.

5.

No warranty coverage is applicable to any equipment used for currency
other than that specified at the time of the purchase.

6.

Seller expressly disclaims any warranty that counterfeit currency will not
activate said equipment.

7.

Seller expressly disclaims any warranty for any losses due to bill manipula-
tion or theft or loss of cash under any circumstances.

8.

Use of the equipment for anything other than its intended and designed use
will void the Limited Warranty Agreement. Use of equipment for anything
other than its intended and designed use includes, but is not limited to,
downloading software/applications not certified by Seller such as e-mail,
spyware, screen savers, viruses, worms, third party software, web search
engines, cookies, spam, desktop applications, games, web surfing, etc.

Seller further warrants all repair or service work performed by a factory trained representative or

Hamilton Manufacturing Corp. for a period of ninety (90) days from the date the repair or service work was
performed. Purchaser’s remedies and the liabilities and obligations of Seller herein shall be limited to repair or
replacement of equipment as Seller may choose, and Seller’s obligation to remedy such defects shall not
exceed the Purchaser’s depreciated value of the equipment. Purchaser EXPRESSLY AGREES this is an
EXCLUSIVE REMEDY under this warranty. There are no other express or implied warranties on repair or
service work performed by a factory trained representative or Hamilton Manufacturing Corp. which extend
beyond the face hereof.

Summary of Contents for Single Stacker



















Reviews: