25
Subject to change without notice
Further information can be found in the section “Data transfer“
of this manual, if the original interface is inserted. If an optio-
nal interface is built in, the attached CD contains additional
information.
6.4 Self Cal
This function key leads to the submenu “Settings Self Cal”. On
condition that the instrument inputs are open an automatic
instrument adjustment may be made by pressing the “Start”
function key. It can be interrupted early by aid of the MENU
OFF pushbutton
37
.
This function optimises the instrument adjustment under the
current environment conditions (temperature).
The automatic calibration (adjustment) optimises the oscillo-
scope behaviour under the current temperature conditions.
It should not be started until a minimum operating time of 30
minutes has elapsed.
7
AUTOSET
(pushbutton)
Choosing AUTOSET will cause an automatic instrument setting,
dependent upon the signal proper which selects positions, signal
amplitude and time base for a reasonable display. In component
test mode, XY mode, or ADD automatically dual channel mode
will be selected. If dual channel or Ch1 or CH2 were previously
chosen this will remain.
AUTOSET will further set the intensity to an average value if it
was set too low. If a menu was opened it will be turned off by
AUTOSET. During the display of HELP texts AUTOSET is not
available.
8
HELP
(pushbutton)
Pressing the HELP pushbutton will turn the signal display off
and display the help text.
If a menu was opened the help text will refer to this menu
respectively to the special menu or submenu option selected.
If a knob is moved another help text referring to this knob will
appear. Press HELP again to deactivate the text.
9
POSITION 1
(knob)
This knob can assume various functions which depend upon
the operating mode, the functions selected with the CH1/2–
CURSOR–TRACE SEP-pushbutton
11
and the menu option
selected.
9.1 Y-position
9.1.1
Y-position CH1
POSITION 1 will set the Y-position of CH1 provided there is
YT-mode and the pushbutton CH1/2–CURSOR–TRACE SEP-
pushbutton
11
is not illuminated.
9.1.2
Y-position of 2
nd
time base B (TRACE SEP); channel 1 and
channel 2
The POSITION 1 control will assume the function of Y-position
control of the channel 1 and channel 2 signal displayed by
time base B in alternate time base mode after the following
procedure. This is convenient in order to be able to separate
the displays of the (same) signal with both time bases on the
screen. Press the HOR VAR pushbutton
26
>
”Search“. Press
the CH1/2–CURSOR–TRACE SEP-pushbutton
11
, select the
function ”TB B“. The pushbutton will light up green.
9.2. X position in XY mode
POSITION 1 will function as X position control of CH1 in XY mode
and provided the CH1/2–CURSOR–TRACE SEP-pushbutton
11
is not illuminated.
STOP
Note:
The HORIZONTAL control
23
will also be functional
in XY mode.
HM 1
0
0
0-2 - KLB - Stand: 07/1
2/06 gw
HM1
0
0
0 - blau - Stand: 07/1
2/06 gw
HM
10
0
0
-2
- gr
ü
n -
St
an
d
:
07/1
2/06
gw
VAR
VAR
VAR
x10
FOCUS
TRACE
VOLTS / DIV
VAR
VOLTS / DIV
VAR
TIME / DIV
VAR
X-POS
INTENS
!
LEVEL A/B
MENU
AUX
AUXILIARY INPUT
HORIZONTAL
INPUTS
1M
Ω
II15pF
max
400 Vp
CAT I
!
CAT I
!
DELAY
TRACE
SEP
CH 1/2
CURSOR
SAVE/
RECALL
AUTOSET
SETTINGS
HELP
POSITION 1
POSITION 2
VERT/XY
HM1500-2
ANALOG
OSCILLOSCOPE
150 MHz
TRIGGER
MODE
FILTER
SOURCE
TRIG
’
d
NORM
HOLD OFF
AUTO
MEASURE
CURSOR
MEASURE
TRIG. EXT. / Z-INP.
CH 1
CH 2
X-INP
CH 1
CH 2
HOR
MAG
1M
Ω
II
15pF
max
100 Vp
20 V
1 mV
20 V
1 mV
0.5s
50ns
POWER
POWER
MENU
MENU
OFF
OFF
1
2
3
4
5
8
7
6
9
10
11
13
12
14
15
22
23
16
17
24
18
21
25
26
19
20
27
30
28
29
31
32
33
37
C o n t r o l s a n d R e a d o u t
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
FAX 781.665.0780 - TestEquipmentDepot.com
