4
Notes on use
•
The
[OK]
button and
►
on the remote control
correspond to the
[POWER/VOLUME/ENTER/
NAVIGATE]
button (5) on the front of the radio.
•
The
◄
button on the remote control corresponds to
the
[ ]
button on the front of the radio
•
The
▲▼
buttons on the remote control correspond
to turning the navigation controller to the left and
right on the front of the radio.
Preparing the remote control for use
Open the cover on the battery compartment. This can
be found on the back of the remote control and can be
opened by sliding in the direction indicated.
The extent of delivery includes two AAA batteries which
must be inserted into the battery compartment for the
remote control to work. When inserting the batteries,
ensure that they are inserted with the correct polarity.
The relevant polarity (+ / -) is marked inside the battery
compartment.
Setting up a network connection
4.1 LAN (wired network)
•
Connect the LAN connection of your router to the LAN
connection on your radio. You will require an Ethernet
cable, which is not included in the delivery, to do this.
•
Make sure that the router is on and working properly, and
that you have an Internet connection.
•
See the operating instructions for your router regarding a
properly functioning LAN connection.
•
Then proceed as described in point 5, “Getting Started”.
4.2 WLAN (wireless network)
•
Ensure that the router is switched on, is functioning
correctly and that there is a connection to the internet.
•
Activate the WLAN function of your router.
•
Follow your router‘s operating instructions as regards the
correct functioning of the WLAN connection.
•
Then proceed directly as described under section 5
‚Getting started‘.
5. Getting started
Note - Optimal reception
"DIR3510SCBTX" has an antenna connection for external
antennas with a coaxial connection. A suitable telescopic
antenna that allows DAB, DAB+ and FM reception is
included in the extent of delivery. Alternatively, you
can use an active or passive antenna to improve the
reception or to adapt it to your requirements.
Please note:
•
Always pull the antenna out completely.
•
We recommend you adjust the antenna vertically to
ensure optimal reception.
5.1 General Notes on Use
5.1.1 Switch On / Off / Standby
•
Press [
POWER/VOLUME/ENTER/NAVIGATE
] (5) to
switch on the radio.
•
Press and hold [
POWER/VOLUME/ENTER/NAVIGATE
]
(5) for 3 seconds to switch the radio off (standby).
•
To completely switch off the device, disconnect it from the
power supply.
5.1.2 Navigation and Control
•
After pressing a shortcut button, navigate through the
menu items using.
•
Select the individual menu items by turning [
POWER/
VOLUME/ENTER/NAVIGATE
] (5).
•
Confirm the selection by pressing [
POWER/VOLUME/
ENTER/NAVIGATE
] (5).
5.1.3 Volume Adjustment
•
Turn the volume up (right) or down (left) by turning
[
POWER/VOLUME/ENTER/NAVIGATE
] (5) accordingly.
5.2 Switching ON
Warning
•
Only operate the product from a socket that has been
approved for the device. The socket must be installed
close to the product and must be easily accessible.
•
Disconnect the product from the power supply using
the On/Off switch – if this is not available, unplug the
power cord from the socket.
•
If using a multi-socket power strip, make sure that the
total power consumption of all connected devices does
not exceed the power strip's maximum throughput
rating.
•
If you will not be using the product for a prolonged
period, disconnect it from mains power.
•
Connect the power supply to the mains connection (2) on
the back of the radio.
•
Connect the network cable to a properly installed and
easily accessible network socket.
•
Wait until the radio has initialised fully.
•
Press [
POWER/VOLUME/ENTER/NAVIGATE
] (5) to
switch on the radio.
