background image

4

5

1  Power LED
2  DTC LED
3  Wi-Fi LED
4  Datalog LED
5  8A HCO LEDs
6  25A HCO LEDs
7  Battery Negative Stud
8  Battery Positive Stud
9  Wi-Fi Antenna (RP-SMA)
10  USB-C Port (Comms)
11  Connector A (Superseal 34-pin Keyway 1)
12  Connector B (Superseal 26-pin Keyway 1)
13  Connector C (Superseal 34-pin Keyway 2)
14  Connector D (Superseal 26-pin Keyway 3)
15  Connector E (DTP-4)
16 Mounting Holes

10

11

12

13

14

15

1 2 3 4

5

6

7

8

9

16

16

NEXUS R5 OVERVIEW

NEXUS R5 LED BEHAVIOUR

 LED 

COLOUR 

CONDITION

 Power  

Green

 

Normal operation (on main power or low power mode)

 

Blue

 

Connect to unit and install firmware

 

Red

 

Hardware fault

 DTC 

None

 

DTCs not present

 

Yellow

 

A DTC is present (of any kind, past/present/not severe/severe)

 

Blue

 

PDM in boot mode - connect to unit and install firmware 

 WiFi 

None

 

Wi-Fi is disabled

 

Green solid

 

Wi-Fi is enabled

 

Green flashing

 

Wi-Fi is enabled and connected to NSP

 Datalog 

None

 

Unit is not logging 

 

Yellow flashing

 

Unit is logging, unit is not looping or not full

 

Yellow

 

Logging, unit is looping or full 

 HCO (all)  

None

 

Channel is off

 

Green

 

Channel is on - duty cycle is >0%  and operating correctly

 

Red

 

Channel is not allowed to be driven. Usually caused by (but not limited to)

 

 

an overcurrent this drive cycle

Summary of Contents for NEXUS R5














Reviews: