background image

3

Natural Gas and Propane versions

Appliance

VBX30

VBX18

Total weight (full)

kg

38.1

32.6

Total weight (empty)

kg

36.1

31.3

Max lift weight

kg

28.1

24.7

Total water capacity

l

2.0

1.3

Electrical supply

230V 50Hz Fuse at 3A

Internal fuse

T4H 4A 250V

Maximum power consumption

W

110

IP Rating

XXXX

Flue gas temperature Nat Gas 80/60(Propane)

°C

73 (76)

74 (72)

Flue gas temperature Nat Gas 50/30

41

43

CO

2

value max rate (Nat Gas)

%

9.2 ± 0.3 case on
9.0 ± 0.2 case off

CO

2

value min rate (Nat Gas) ref only

%

8.9 ± 0.1

8.4 ± 0.1

CO value max rate (Nat Gas)

%

0.01 ± 0.005

CO

2

value max rate (Propane)

%

10.7 ± 0.3 case on
10.5 ± 0.2 case off

CO

2

value min rate (Propane) ref only

%

10.0± 0.1

9.7 ± 0.1

CO value max rate (Propane)

%

0.019 ± 0.005

Flue products mass flow rate (Nat Gas)

g/s

13.7

8.3

Flue products mass flow rate (Propane)

g/s

13.7

8.3

Gas Valve Offset @ min rate

Pa

-3.0

Connections

Gas

15 mm compression

CH flow

22 mm tail 

CH return

22 mm tail 

Condensate Drain

21.5  - 22 mm plastic overflow pipe

2.3

GENERAL SPECIFICATIONS

34

Refer to Figure 49.

Key

G C Part No.

Description

No off

Makers Pt No.

1

Ignition Electrode

500680

2

Detection Electrode

500681

3

Spark Generator Unit

500665

4

Gas Control Valve

500655

5

Fan Assembly

601015

6a

Burner VBX 30/SBX 30

700602

6b

Burner VBX 18/CBX 24

700600

7a

Heat Exchanger (VBX 30)

451033

7b

Heat Exchanger (VBX 18)

451034

8

Water Temperature Sensor

500661

9

Flue Sensor

500660

10

Manual Bleed Valve

300730

11

Control PCB

988491

12

User Interface

988492

Heat Exchanger Seal Kit

988489

SHORT PARTS LIST

10

49

1

2

3

4

5

6

7

8

9

10

11

12

Summary of Contents for VBX 18





















Reviews: