Haier YR-HD Service Manual Download Page 61

Page: 61 / 143

Indoor Unit Installation

Make a hole of 70 mm in diameter, slightly descending to outside the
wall

Install piping hole cover and seal it off with putty after installation

Indoor/outdoor electric cable and drain hose must be bound with

efrigerant

piping by protecting tape.

[ Other direction piping ]

Cut away, with a nipper, the lid for piping according to the piping

direction and

then bend the pipe according to theposition of wall

hole. When bending, be careful not to crash pipes.

Connect beforehand the indoor/outdoor electric cable,

and then

pull out the connected to the heat insulation of connecting part
specially.

Making a Hole on the Wall and Fitting the Piping Hole
Cover

Drawing of pipe

[ Rear piping ]

Draw pipes and the drain hose, then fasten them with the adhesive
tape

3. Coat the

aring seal face with refrigerant oil and connect pipes.

Cover the connection part with heat insulation materials closely,
and make sure

xing with adhesive tape

Remove terminal cover at top right corner of indoor unit,and then

take

off wiring cover by removing its screws.

Indoor side

Outdoor side

Ø70mm

Wall hole

Thickness of wall

(Section of wall hole)

Piping hole pipe

Fixing the indoor unit body

Connecting the indoor/outdoor Electric Cable

Removing the wiring cover

Installation of the Indoor Unit

Removal of Front Grille

Hold the front panel by the tabs on the both sides and lift it until it
stops with a click.

Loosen the marked five screws and open the grille

Fix with adhesive
tape

Lid for left piping

Heat insulation
material

Drain hose

Piping

Pipe supporting
plate

Indoor/outdoor electric cable

Lid for right
piping

[ Left

Left-rear piping ]

In case of left side piping, cut away, with a nipper, the lid for left

piping.

In case of left-rear piping, bend the pipes according to the piping

direction to

the mark of hole for left-rear piping which is marked on

heat insulation materials.

1. Insert the drain hose into the dent of heat insulation materials of

indoor unit.

2. Insert the indoor/outdoor electric cable from backside of indoor

unit, and pull it out on the front side, then connect them.

Remove the front panel,then use two fastening screws to fix

the unit on the floor. As the figure shown.

Once refrigerant piping and drain piping connections are

complete,fill the gap of the through hole with putty.Attach the

front panel and front grille in their orginal positions once

all connections are complete.

Domestic air conditioner

System configuration

252

Summary of Contents for YR-HD
















































































































































Search results

Summary of Contents for YR-HD

Reviews:

Related manuals for YR-HD

Brands by name

Popular brands

Haier YR-HD, Service Manual

Search results

Summary of Contents for YR-HD

Reviews:

Related manuals for YR-HD

Brands by name

Popular brands