Haier YR-HD Service Manual Download Page 102

Page: 102 / 143

System configuration

Domestic air conditioner

the power supply cord
and so on.

Do not install in the place where there is any

possibility of inflammable gas leakage around the unit.

3.Do not

get the unit exposed

to vapor or oil steam.

Cautions

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.

Connect the earth
cable.

earthing

WARNING

When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.

OFF

Use an exclusive
power source
with a circuit
breaker

ENFORCEMENT

Connect power supply cord
to the outlet completely

Use the proper voltage

Do not use power supply
cord in a bundle.

Take care not to damage

the power supply cord.

1.Do not use power supply cord extended
or connected in halfway

STRICT

ENFORCEMENT

STRICT

ENFORCEMENT

PROHIBITION

Do not start or stop the

operation by disconnecting

Do not channel the air flow directly
at people, especially at infants or
the aged.

Do not try to repair or
reconstruct by yourself.

Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.

CAUTION

Take fresh air occasionally especially
when gas appliance is running at the
same time.

PROHIBITION

STRICT

ENFORCEMENT

Do not operate the switch with
wet hand.

PROHIBITION

Do not install the unit near a fireplace
or other heating apparatus.

Check good condition of the
installation stand

Do not pour water onto the unit
for cleaning

PROHIBITION

Do not place animals or plants in
the direct path of the air flow

Do not place any objects on or
climb on the unit.

Do not place flower vase or water
containers on the top of the unit.

Do not insert objects into the air

inlet or outlet.

PROHIBITION

STRICT
ENFORCEMENT

Check proper
installation of the
drainage securely

WARNING

359

Summary of Contents for YR-HD
















































































































































Search results

Summary of Contents for YR-HD

Reviews:

Related manuals for YR-HD

Brands by name

Popular brands

Haier YR-HD, Service Manual

Search results

Summary of Contents for YR-HD

Reviews:

Related manuals for YR-HD

Brands by name

Popular brands