Haier YR-HD Service Manual Download Page 11

Page: 11 / 143

Super Match

Installation Manual For Wire Controller

1. Take down wire controller from the holder

2. Install the controller holder

According to the position of 2 screw holes on the holder, drill 2 holes on the wall, and strike the wood stopper to the holes
respectively.

Then align the 2 screw holes of wired controller holder to the wood stopper, fix the holder on the wall with wood screw.

3.Wiring instruction

Use shielded wire between indoor and wire controller. And be earthed on one side, or the unit will not work normally
because of interference.

Note:

Try a wall as flat as possible for installation. Don't use excessive force to tighten screws, otherwise, the holder will be

damaged.

Note:

Confirm the terminal connection firmly, and do not get in tough with shielded wire.

Don't touch the PC panel with your hands.

4.Place wire controller on the holder, and pay attention not to pressing any wires.

5. Wiring connections of wire controller:

Wire controller

Screw holes

shielded wire

grounding

Bracket

TYPE1: For AD09~24SS1ERA(N)(P) AD09~24SS1ERA(N) AD12/18MS1ERA AD12/18MS1ERA(D) AD24MS2ERA AD24MS2ERA(D)

144

Summary of Contents for YR-HD
















































































































































Search results

Summary of Contents for YR-HD

Reviews:

Related manuals for YR-HD

Brands by name

Popular brands

Haier YR-HD, Service Manual

Search results

Summary of Contents for YR-HD

Reviews:

Related manuals for YR-HD

Brands by name

Popular brands