background image

 

59 

APPENDIX A - SPECIFICATIONS 

 
Size: 

Controller:  9.1W x 12.1H x 3.5D 

 

Console: 

4.6W x 4.5H x 1.2D 

 
Weight: 

Controller:    approx. 4.5 lb. 

 

Console:  

approx. 0.5 lb. 

 
Operating 

 

32 - 122 degrees F (0 - 50 degrees C) 

Ranges:   

 

10 - 95 % relative humidity, non-condensing 

 
Power:   

 

120 VAC, 60 Hz, 60 watts 

 
Transformer: 

 

16.5 VAC, 40 VA, 50/60 Hz 

 
Battery:   

 

Sealed Rechargeable Lead-Acid, 12 volts 

 
Bell Fuse: 

 

Polyfuse: 1.35 A 

 
Device Fuse: 

 

Polyfuse: .9 A 

 
Output Fuse: 

 

Polyfuse: .3 A 

 
Battery Fuse: 

 

Polyfuse: 2.5 A 

 
Polyfuses are permanent fuses that do not need replacement. 
 
Nominal Output Voltage:  10-13.8 VDC 
 
Low Voltage Cut Out: 

approx. 9 VDC 

 
Typical Current Consumption at Nominal Voltage:   
 
 Controller: 

105 

mA 

 

 

   

 

Console: 

backlight off, 35 mA 

 

   

 

backlight on, 100 mA 

 

 
CONTROLLER OUTPUTS 

 

 

 

 

UL RATINGS   

MAXIMUM 

 
Devices:   AUX 12 VDC, CONSOLE, and OUTPUTS 1 and 2: 

200 mA  

 

500 mA 

 
Bell: 

BELL 

      350 

mA 

  1 

 
Outputs:   OUTPUTS 1 and 2, each, maximum: 

 

 

100 mA  

 

100 mA 

 
Backup:  Required battery backup hours:   

 

 

24 hours  

 

 
Battery: 

Recommended 

Battery: 

    7 

Ah 

  14 

Ah

Summary of Contents for OMNI LT







































































Reviews: