HADEF 62/05 S Installation, Operating And Maintenance Instructions For The Installer And The User Download Page 7

 

 

 

 

5.52.420.00.01.09 

 

 

 

Transport and Storage 

 

   

CAUTION!

 

Transport  may  only  be  done  by  qualified  personnel.  No  liability  for  any  damage  resulting  from  improper 
transport or improper storage. 

 

3.1 

Transport 

 The devices are checked and if so adequately packed before delivery. 

  Do not throw or drop the equipment.  

  Use adequate means of transport. 

Transport and means of transport must be suitable for the local conditions. 

3.2 

Safety device for transport 

 

NOTICE!

 

Should a safety device for transport exist, please remove it before commissioning. 

3.3 

Storage 

  Store the equipment at a clean and dry place. 

  Protect the equipment against dirt, humidity and damage by an appropriate cover. 

  Protect hooks, wire ropes, chains and brakes against corrosion. 

 

Description  

 

 

 

4.1 

Areas of application 

The devices must be as far as possible installed in a covered room. 

If they are used in the open, protect the units against the effects of weather such as rain, hail, snow, direct 
sunshine,  dust,  etc.  -  we  recommend  to  use  a  cover  in  parking  position.  If  the  device  is  set  up  in  a 
continuously  humid  environment  with  strong  temperature  fluctuations,  the  correct  functionings  are 
endangered by the forming of condensation. 

 

During longer downtimes of motor-operated units, the brake may reduce the function by corrosion. 

 

NOTICE!

 

Use only in the intended atmosphere with a humidity of up to 100%, but not under water! 

 

 

 

   

DANGER!

 

In particular, use is not permitted: 

    for tearing loose fixed loads, dragging of loads as well as diagonal pulling  

   for pulling against a fixed point without additional safety and/or measuring equipment against exceeding 

the nominal load 

    in  potentially  explosive  atmospheres,  unless  the  equipment  has  been  modified  for  this  purpose  and                    

this is shown on special type plates it carries for this purpose. 

    in reactor containments 

    for transporting persons  

    for holding lifted loads 

    for scenic use 

    when persons are under suspended loads 

 

4.2 

Design 

HADEF electrical chain hoists are equipped with a suspension eye for stationary use. The one and two chain 
fall devices may optionally be equipped with a suspension hook.  

All devices can also be supplied with monorail trolley with push travel, hand geared or electric drive. 

Summary of Contents for 62/05 S


























Reviews: