habitat et jardin Luzern 727 Manual Download Page 2

2

Dear summerhouse owner,

impossible to completely prevent some degree of warping, the

formation of resin and cracks, especially on the outside surfaces

and is not actually a defect in the quality

Incidentally:

We wish you every success and lots of fun with the construction of your log cabin . . .
Now you can get started...

Your cabin was manufactured with the greatest care and expertise from good quality, well-dried, fine-
grained spruce.

The material we use is purely natural, and being solid wood is vigorous and active. Despite technical
drying methods it is, nonetheless,

The varying knot formations are

also typical of spruce. These variations are all part of the beauty of wood.

Any rough edges and unevenness caused by the planer etc. on the back of the profiled planks and
floorboards is due to production techniques and

The timber used (which is, of course, from sustainable forests) is absolutely untreated, except for the

to avoid by applying a coat of stain(blue-stain inhibitor is recommended) or

paint – please, take notice of the recommendations of the varnish or paint manufacturer. It is not
advisable to paint the wall timbers before assembling them – this is best done when the cabin has been
erected and the weather is fine. However, if you wish to paint odd parts in different colours, this should
be done before the cabin is assembled.

adequate ventilation and avoiding waterlogging are still the best ways

of protecting wood against rot.

.

.

Teknogrund treated parts. That means that the untreated wood will turn greyish over the years, something
which you might choose

Please check the content of the package before you start building your cabin and contact your

dealer if something is missing or can not be used for the purpose. Claims are not accepted after the
product has been assembled.

®

Note!

Dear Customer,
in a case of reclamation, please inform your dealer about the specific guarantee number of your
cabin. You can find this number on the package and on the door or the door frame, marked by the
hinge in the upper third part of the door or the frame. Unfortunately, without this guarantee
number we cannot handle your reclamation!

Luzern

271205

Summary of Contents for Luzern 727













Reviews: