Habasit PM-306/160 Use And Maintenance Manual Download

Page: 36 / 78

Habasit Italiana S.p.A.
Vittorio Veneto 31029 (TV)
Tel.: ++39(0)438.9113
Fax. ++39(0)438.200545

Hot Press PM-306/160

Author:

A.T. / KM

INSTALLATION

Edition: 09/2005

Page

C-8

Replaces:

C.5

Storage

IMPORTANT

The hot-pressing device must be stored in a dry room free from seepage of liquids.

NOTE

Never, on any account, store the hot-pressing device out of doors! As a general rule, observe the

following environmental conditions.

ABLE

TORAGE CONDITIONS

Environmental conditions for storage

Min/Max ambient temperature of storage

In the range of +5 °C to +40 °C

Relative humidity of place of storage

In the range of 50% to 70%

If the hot-pressing device, its accessories and spares have to remain in storage for a prolonged period,
they must be protected from dust and damp.

We recommend the following:

Clean the hot-pressing device in general.
Apply PROTECTIVE SILICONE OIL to

-painted or

-treated parts.

Cover the hot-pressing device with a sheet to protect it from dust.
Before being oiled or greased for good preservation, some parts can, if necessary, be cleaned with a
specific, rustproofing detergent.

Hot-pressing device PM-306/160

Summary of Contents for PM-306/160















































































Search results

Summary of Contents for PM-306/160

Reviews:

Related manuals for PM-306/160

Brands by name

Popular brands

Habasit PM-306/160, Use And Maintenance Manual

Search results

Summary of Contents for PM-306/160

Reviews:

Related manuals for PM-306/160

Brands by name

Popular brands