H3C UniServer R4900 G5 Operating System Installation Manual Download Page 140

Page: 140 / 141

OS installation takes a long time when the OS
image is mounted through an HDM shared
network interface

Symptom

OS installation takes a long time when the link speed is 1000 Mbps between an HDM network
interface and the peer interface.

Solution

To resolve the issue:

Change the transmission rate of the peer interface to 100 Mbps because the shared network
interface supports autonegotiation.

If the issue persists, contact H3C Support.

CAS E0306 OS installation failure

CAS E0306 OS installation is not supported because this version does not contain the Smartpqi
driver required by PMC SmartIOC 2100/SmartROC 3154.

Blue screen or other errors occurred when the
chipset driver is updated on an R5300 server
installed with the Windows Server 2016 OS

Install the most recent patch file for the Windows system.

Summary of Contents for UniServer R4900 G5














































































































































Search results

Summary of Contents for UniServer R4900 G5

Reviews:

Related manuals for UniServer R4900 G5

Brands by name

Popular brands

H3C UniServer R4900 G5, Operating System Installation Manual

Search results

Summary of Contents for UniServer R4900 G5

Reviews:

Related manuals for UniServer R4900 G5

Brands by name

Popular brands