H3C UniServer R4900 G5 Operating System Installation Manual Download Page 134

Page: 134 / 141

Storage controller HBA-H460-M1 FW1.04 can be
installed successfully on an RHEL OS but the
system prompts installation failure

Symptom

The HBA-H460-M1 storage controller with version FW1.04 can be installed successfully on an RHEL
OS but the system prompts installation failure.

Solution

To resolve the issue:

Install the

aacraid

drive on the RHEL OS.

Add a space before and after the

aacraid

field in

/etc/dracut.conf.d/aacraid.conf

, and then

save the configuration.

Figure 242 Adding spaces

Install the

smartpqi

driver.

Reboot the server and verify that the

smartpqi

driver has been installed successfully.

If the issue persists, contact H3C Support.

Bluescreen or kernel error occurred when BIOS
NUMA is enabled and IMC0 and IMC1 for CPU 1
or CPU 2 are disabled

Symptom

A blue screen or a kernel error occurred after a server reboot when the following conditions are met:

•

The operating system is installed on the logic disk of the storage controller.

•

BIOS NUMA is enabled and IMC0 and IMC1 for CPU 1 or CPU 2 are disabled.

Summary of Contents for UniServer R4900 G5














































































































































Search results

Summary of Contents for UniServer R4900 G5

Reviews:

Related manuals for UniServer R4900 G5

Brands by name

Popular brands

H3C UniServer R4900 G5, Operating System Installation Manual

Search results

Summary of Contents for UniServer R4900 G5

Reviews:

Related manuals for UniServer R4900 G5

Brands by name

Popular brands