H3C HIM-16GBP Interface Manual Download Page 20

Page: 20 / 102

Figure 12 Front panel

(1) Captive screw

(2) Ejector lever

(3) SFP port carrier signal LED (LINK/ACT)

(4) SFP port loopback/alarm LED (LP/AL)

(5) SFP port 3 (155 Mbps) or SFP port 1 (622 Mbps)

(6) SFP port 2 (155 Mbps) or SFP port 0 (622 Mbps)

(7) SFP port 1 (155 Mbps)

(8) SFP port 0 (155 Mbps)

LEDs

Table 13 LED description

LED

Status

Description

LINK/ACT

(Green)

Off

No link is present.

A 155.52/622.08 Mbps link is present.

Flashing

The SFP port is receiving or sending data at 155.52/622.08 Mbps.

LP/AL

(Yellow)

Off

No loopback or alarm exists.

The port is in loopback state.

Flashing

There is a minimum of one alarm.

Interface specifications

Table 14 Interface specifications

Item

Specification

Connector type

SFP/LC

Number of interfaces

•

HIM-MSP2P: 2 OC-3 interfaces or 1 OC-12 interface

•

HIM-MSP4P: 4 OC-3 interfaces or 2 OC-12 interfaces

Interface standards

•

SONET STS-3/STS-12

•

SDH STM-1/STM-4

Interface speed

155.52/622.08 Mbps

Interface cables

The HIM-MSP2P/HIM-MSP4P must work with an SFP transceiver module and an optical fiber with
LC-type connectors. For the appearance and connection of a HIM-MSP2P/HIM-MSP4P interface
cable, see "

Connecting an optical interface cable

Summary of Contents for HIM-16GBP







































































































Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands

H3C HIM-16GBP, Interface Manual

Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands