H3C HIM-16GBP Interface Manual Download Page 38

Page: 38 / 102

Front panels

Figure 27 Front panel of MIM-8E1(75)

(1) DB-68 connector

(2) Carrier signal LED (LINK/ACT)

(3) Captive screw

(4) Loopback/alarm LED (LP/AL)

Figure 28 Front panel of MIM-8E1(75)-F

The front panel of MIM-8E1(75)-F is similar to that of MIM-8E1(75).

LEDs

Table 39 LED description

LED

Status

Description

LINK/ACT

(Green)

Off

No carrier signals are being received.

Carrier signals are being received.

Flashing

Data is being transmitted or received.

LP/AL

(Yellow)

Off

No loopback or alarms have occurred.

The interface is in loopback state.

Flashing

A minimum of one alarm of the type of AIS, LFA, or RAI has
occurred.

Interface specifications

Table 40 Interface specifications

Item

Specification

Connector type

DB-68

Number of interfaces

Interface standard

G.703

Interface speed

2.048 Mbps

Interface cable type

75-ohm 8E1 splitter cable

Cable characteristic impedance

75 ohm

Working modes

E1, CE1, and FE1 (supported by the MIM-8E1(75)-F only)

Summary of Contents for HIM-16GBP







































































































Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands

H3C HIM-16GBP, Interface Manual

Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands