H3C HIM-16GBP Interface Manual Download Page 60

Page: 60 / 102

MIC-X-XP4W

A MIC-X-XP4W is a 10-GE interface module. It provides four 10-GE SFP+ ports and supports
switchover between LAN/WAN modes.

Front panel

Figure 48 Front panel

(1) Captive screw

(2) 10GBASE-R/W-SFP+ ports

(3) SFP+ port LED (LINK/ACT)

LEDs

Table 74 LED description

LED

Status

Description

LINK/ACT

Flashing

Data is being received or transmitted.

Steady on

A link is present.

Off

No link is present.

Interface specifications

Table 75 Interface specifications

Item

Specification

Connector type

SFP+/LC

Number of interfaces

Supported physical layer type

10GBASE-R

Interface speed

10.3125 Gbps

For the transceiver modules available for a MIC-X-XP4W interface module, see

Table 104

Interface cables

For the appearance and connection methods of the interface cables, see "

Connecting an optical

interface cable

MIC-X-GT8

A MIC-X-GT8 GE copper interface module provides eight 10/100/1000BASE-T ports.

Summary of Contents for HIM-16GBP







































































































Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands

H3C HIM-16GBP, Interface Manual

Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands