manualshive.com logo in svg

H3C H3C S7503 S7506 AND S7506R SWITCH, Installation Manual, Page: 93 / 144

Share
Download
H3C H3C S7503 S7506 AND S7506R SWITCH Installation Manual Download Page 93

Installation Manual 

H3C S7502 Ethernet Switch 

Chapter 4  Hardware Installation

 

4-14 

  Caution: 

When the optical port has not been connected with a fiber connector or its dustproof 
cover is open, there might be some invisible radiation emitted from the optical port. So 
do not stare into the optical port directly. 
Cover the optical port if there is no connector plugged in. 

 

4.7  Cabling 

4.7.1  Table-Mounted Switch 

If the chassis of a switch stands alone, you do not have to care about the inside or 
outside cabinet cabling. All the port service cables can run along the left side of the 
chassis (cabling channel), and the chassis power cables can run upward or downward 
based on the specific conditions in the equipment room (lightning protection box, 
terminal bar etc).  

4.7.2  Rack-Mounted Switch 

For the switches are mounted in a 19-inch standard rack, the service cables can be 
bound to the cable binding rack at the left side of the chassis and be arranged to run on 
the cable rack or in the raised floor according to the situation in an exchange equipment 
room (whether the signal cable of the room is accessed from the cable rack on the top 
of the chassis or the cable channel under the floor.) Collect all the transit data signal 
cable connectors and locate them on the floor of the chassis instead of any places 
outside the chassis for fear of unexpected damage. The power cables run out of the 
rear left of the chassis and either on the cable rack or in the raised floor as near as 
possible based on the specific conditions in the equipment room (lightning protection 
box, terminal bar etc).   

4.8  Cable Binding 

4.8.1  Use of Labels 

Correctly edit the label and paste it to a proper place on the bound cables.  

4.8.2  Precautions for Cable Binding 

z

 

Bind the cables straight in the cabinet. No twisting or bending. 

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

















































































































































Reviews:

No comments