manualshive.com logo in svg

H3C H3C S7503 S7506 AND S7506R SWITCH, Installation Manual, Page: 136 / 144

Share
Download
H3C H3C S7503 S7506 AND S7506R SWITCH Installation Manual Download Page 136

Installation Manual 

H3C S7502 Ethernet Switch 

Appendix A  Installation of Lightning Arrester for AC Power

 (Lightning Protection Grounding Strip)

 

A-2 

  Caution: 

z

 

Make sure that the arrester is well grounded before using the lightning arrester for 
power. 

z

 

After inserting AC power cable connector of switch into the socket of lightning 
arrester, if the green LED is on and the red LED does not alarm, the lightning 
arrester of power is running and the function of lightning protection has taken effect. 

z

 

Pay adequate attention if the red LED is on. You should correctly locate the problem, 
whether it is caused because the grounding cable of the arrester is not well 
grounded or because the live and zero wires are connected in reverse direction. 
You may check that in the following way. When the red LED is on, use a multimeter 
to examine polarity at the power socket of the arrester. If it is same to that of the 
power socket in the equipment room, it means that arrester is not well grounded. If it 
is adverse to that of the power socket in the equipment room, it means that the 
power socket of the arrester is set to the reverse polarity. In this case, you should 
open the power socket of arrester to correct polarity. After that, if the red LED still 
alarms, it means that the arrester is not well grounded yet. 

 

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

















































































































































Reviews:

No comments