manualshive.com logo in svg

H3C H3C S7503 S7506 AND S7506R SWITCH, Installation Manual, Page: 36 / 144

Share
Download
H3C H3C S7503 S7506 AND S7506R SWITCH Installation Manual Download Page 36

Installation Manual 
H3C S7502 Ethernet Switch 

Chapter 1  Product Overview

 

1-30 

 

Figure 1-30 

Appearance of an external PoE power supply 

 

 

  Note:  

z

 

The S7502 supports a PoE power supply with up to 1500 W power output. A single 

PoE module can provide 1250 W power output, and two can provide up to 2400 W 

power output in the case that PSE2500-A3 supplies 100 VAC to 140 VAC input 

voltage. Three PoE modules are required to provide output power of 2400 W if 

power supply redundancy is desired. With 200 VAC to 240VAC input voltage, a 

single PoE module can provide 2500 W power output. Two PoE modules are 

required to provide 2500 W power output if power supply redundancy is desired. 

z

 

There are S7502 PoE chassis and non-PoE chassis. If the PoE function is required, 

select an S7502 PoE chassis. 

 

1.11.6  Fan Tray 

The fan tray is on the right side of an S7502 chassis, and directly connected to the 

backplane through a connector. The fan fault signals are summarized and transmitted 

from the backplane to the SRPU for further processing. The fan tray is hot-swappable. 

 

Figure 1-31 

Fan tray on an S7502 

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

















































































































































Reviews:

No comments