H3C H3C S7503 S7506 AND S7506R SWITCH Installation Manual Download Page 7

Page: 7 / 144

Installation Manual
H3C S7502 Ethernet Switch

Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 General Information

1.1.1 Preface

H3C S7500 Series Ethernet Switches are modular, large-capacity Layer 2/3 Ethernet

switches that support wire-speed forwarding. The S7500 series include S7502, S7503,

S7506, and S7506R.

The S7503, S7506, and S7506R are designed to operate at the convergence layer

of IP metropolitan area networks (MANs) and at the core layer of small to

medium-sized enterprise networks and campus area networks.

The S7502 is designed to operate at the core layer of small to medium-sized

enterprise networks and at the convergence layer and access layer of IP MANs.

The S7502 is a high-capacity, cost-effective Layer 3 Ethernet switch. It provides

high-density GE/FE ports, as well as modularized components that enable you to

configure flexibly according to your specific needs.

Figure 1-1

S7502 in a MAN

The S7502 supports 1+1 AC power redundancy backup, and provides one switching

and routing processing unit (SRPU) slot and one line processing unit (LPU) slot. Both

the SRPU and the LPU can provide high-density service ports.

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

















































































































































Search results

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

Reviews:

Related manuals for H3C S7503 S7506 AND S7506R SWITCH

Brands by name

Popular brands

H3C H3C S7503 S7506 AND S7506R SWITCH, Installation Manual

Search results

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

Reviews:

Related manuals for H3C S7503 S7506 AND S7506R SWITCH

Brands by name

Popular brands