manualshive.com logo in svg

H3C H3C S7503 S7506 AND S7506R SWITCH, Installation Manual, Page: 107 / 144

Share
Download
H3C H3C S7503 S7506 AND S7506R SWITCH Installation Manual Download Page 107

Installation Manual 

H3C S7502 Ethernet Switch 

Chapter 6  Hardware Maintenance

 

6-1 

Chapter 6  Hardware Maintenance  

 

  Caution: 

The power modules of the S7502 are hot-swappable. 
When installing or replacing an in-service power module, pay attention to operations 
and electrical safety. Do not touch any naked wire, terminal or any part of the product 
labeled with a high-voltage warning to avoid injury. 

 

6.1  Required Tools 

z

 

ESD-preventive wrist strap 

z

 

Screwdriver 

6.2  Removing and Installing Power Module 

2

2

1

 

Figure 6-1 

Install a power module 

6.2.1  Installing a Power Module 

1)  Wear an ESD-preventive wrist strap and take the new power module out of the 

package. Check that the input mode (DC or AC) of the power module is correct. 

2)  Grasp the handle of the module with one hand and hold the module bottom with 

the other. Slide the module slowly along the guide rail into the chassis. See 

①

 in 

Figure 6-1. Ensure the module is well contacted with the guides. 

 

Summary of Contents for H3C S7503 S7506 AND S7506R SWITCH

















































































































































Reviews:

No comments