H3C CR19000-16 Installation, Quick Start Download Page 35 | Manualshive

Page: 35 / 46

background image

9-2

Figure 9-2 Installing a fabric module

Installing a filler panel in a fabric module slot

1.

Loosen the captive screws on the ejector levers of the filler panel and then open the ejector
levers.

2.

Align the filler panel with the fabric module slot. Push the filler panel slowly into the slot along
the guide rails.

3.

Continue to push the filler panel until the brakes on its ejector levers touch the slot edges
tightly. Then simultaneously close the ejector levers.

4.

Fasten the captive screws on the ejector levers.

«
...
33
34
35
36
37
...
»

Summary of Contents for CR19000-16















































Reviews:

No comments

Related manuals for CR19000-16

Brand: N-Tron Pages: 18

Brand: JB Systems Light Pages: 15

S5560S-EI Series

Brand: H3C Pages: 37

OfficeConnect WX4400

Brand: 3Com Pages: 528

Brand: DANLERS Pages: 2

Matrix DFE-Gold 4G4202-60

Brand: Enterasys Pages: 78

Brand: ZENEC Pages: 16

Brand: Zamel Pages: 2

Brand: Eaton Pages: 43

Brand: N-Tron Pages: 20

Brand: Lindy Pages: 5

Brand: Lancom Pages: 21

Brand: Racal Instruments Pages: 53

Brand: Xantech Pages: 12

Brand: Lanpro Pages: 16

Brand: J-Tech Digital Pages: 81

Brand: PCB Piezotronics Pages: 31

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands