H2X THERAPOOL SE Owner'S Manual Download

Page: 85 / 108

DO NOT DIVE.

108

DO NOT DIVE.

Miscellaneous Messages

SENSOR BALANCE IS POOR

The temperature sensors MAY be out of sync by 2°F or 3°F. Call for service.

SENSOR BALANCE IS POOR*

The temperature sensors failed to balance and have remained out of sync for more than 1 hour.
Call for service.

SENSOR FAILURE – SENSOR A, SENSOR B

A temperature sensor or sensor circuit has failed. Call for service.

* This message can be reset from the topside panel with any button press.

NO COMMUNICATIONS

The control panel is not receiving communication from the System. Call for service.

°F OR °C IS REPLACED BY °T

The Control System is in Test Mode. Call for service.

Swim spa Controls

Sensor Related Messages

Summary of Contents for THERAPOOL SE













































































































Search results

Summary of Contents for THERAPOOL SE

Reviews:

Related manuals for THERAPOOL SE

Brands by name

Popular brands

H2X THERAPOOL SE, Owner'S Manual

Search results

Summary of Contents for THERAPOOL SE

Reviews:

Related manuals for THERAPOOL SE

Brands by name

Popular brands