background image

 8 

Inflation and deflation instructions for the BEDI child car seat 

 
Fig. 2 Valve 

 

 

The valve located in the upper rear part of the backrest allows inflation and deflation of the 
child car seat.  When handling with valve follow figure 2. 

Child car seat inflation: 

Remove the child car seat from the packaging, unfold and check the condition of the whole 
child car seat and especially the valve. If the child car seat is in undamaged and complete 
condition, you can inflate it. Remove the plastic cap “a” from the filling valve end that is 
attached to the filling valve body “b” by means of a flexible tape with a sleeve. Thus the 
mouthpiece is uncovered which is equipped with a clack valve inside.  
Carry out the inflation either by mouth or by means of mechanical pump.  The clack valve 
will open due to the pressure of the air being inflated and the air will stream into the child car 
seat.   
At pressure release on mouthpiece the filling valve turns off automatically. 
Inflate as long as the safety –relief valve located on the child car seat side part opens (by 
putting the hand to the valve you will feel escaping air). Repeat the inflation of the child 
restraint system whenever you have suspicion of pressure decrease. 
After completed inflation the safety-relief valve turns off by itself after short while, too. 
In this way we achieve the correct operating pressure in the child car seat. 

 
The child car seat deflation: 

Remove the plastic cap “a” and insert the part “c” on the flexible tape into the mouthpiece. 
The air starts to escape out of the child car seat. Leave the cap in this position during the 
whole time of the child car seat deflation. At the same time roll the child car seat from the 
farthest end towards the filling valve for the most air to escape from the child car seat.  Then 
release the cap and put it on the filling valve end. 
 
 
 

 

 
 
 

Summary of Contents for child car seat




















Reviews: