Gude Expert Power Control 8042 Series Page 41 Manual Download

Page: 41 / 96

Expert Power Control 8042

Configuration

Enable IP filter: Enable or disable the IP filter here. The IP filter represents an access
control for incoming IP packets.

Please note that when IP access control is enabled HTTP and SNMP only work if

the appropriate servers and clients are registered in the IP access control list.

If you choose a wrong IP ACL setting and locked yourself out, please activate the

Bootloader Mode and use GBL_Conf.exe to deactivate the IP ACL. Alternatively, you
can reset the device to factory default.

3.2.3

HTTP

HTTP Server option: Selects whether access is possible only with HTTP, HTTPS, or
both.

Server port HTTP: Here can be set the port number of the internal HTTP. Possible val-
ues ?

are from 1 to 65534 (default: 80). If you do not use the default port, you must ap-

pend the port number to the address with a colon to address the device from a web
browser. Such as: "http://192.168.0.2:800"

Server port HTTPS; The port number to connect the web server via the SSL (TLS) pro-
tocol.

Enable Ajax autorefresh: If this is activated, the information of the status page is auto-
matically updated via http request (AJAX).

For some HTTP configuration changes a firmware reset is required. This can be

done in the Maintenance web page. A restart of the device leads by no means to a
change of the relay states.

Summary of Contents for Expert Power Control 8042 Series

































































































Search results

Summary of Contents for Expert Power Control 8042 Series

Reviews:

Related manuals for Expert Power Control 8042 Series

Brands by name

Popular brands

Gude Expert Power Control 8042 Series, Manual

Search results

Summary of Contents for Expert Power Control 8042 Series

Reviews:

Related manuals for Expert Power Control 8042 Series

Brands by name

Popular brands