Gude Expert Net Control 2304 Page 84 Manual Download | Manualshive

Page: 84 / 87

background image

84

Expert Net Control 2304

© 2021 GUDE Systems GmbH

Support

5. Can you enter multiple e-mail recipients?

·

Yes. In the E-Mail configuration in the Recipient Address field, it is possible to enter
multiple e-mail addresses separated by commas. The input limit is 100 characters.

6. Why did the MIB tables change after the firmware update?

·

Since the number of possible event types was increased, the previous trap design
resulted in an excess of trap definitions: See Change in Trap Design

.

7. Importing an older firmware

·

During a firmware update, old data formats are sometimes converted to new struc-
tures. If an older firmware is newly installed, the configuration data and the energy
meters may be lost! If the device then does not run correctly, please restore the fact-
ory settings (e.g. from the Maintenance Page

).

8. Disable switching events

·

You can set the sending of syslog, emails etc. when switching ports (only concerns
Gude devices with relays) under "System" in the sensor configuration

.

56

18

46

«
...
82
83
84
85
86
...
»

Summary of Contents for Expert Net Control 2304
























































































Reviews:

No comments

Related manuals for Expert Net Control 2304

Brand: OmarLift Pages: 14

Brand: Handicare Pages: 56

Brand: tams elektronik Pages: 60

Gemini GEM-P9600

Brand: NAPCO Pages: 6

Gemini GEM-P816

Brand: NAPCO Pages: 56

Brand: IBA Pages: 29

Brand: Maximum Controls Pages: 58

Brand: FUTABA Pages: 8

CentralControl CC41

Brand: Becker Pages: 48

Brand: GSK Pages: 32

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: phytron Pages: 55

Q.PEAK DUO XL-G11S.X / BFG Series

Brand: Qcells Pages: 26

Brand: EpiSensor Pages: 37

Brand: Potter Pages: 25

Brand: National Instruments Pages: 4

Brand: ICP DAS USA Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands