Gude Expert Net Control 2304 Page 34 Manual Download

Page: 34 / 87

Expert Net Control 2304

Configuration

SNMP-get: Enables the acceptance of SNMP-GET commands.

SNMP-set: Allows the reception of SNMP-SET commands.

SNMP UDP Port: Sets the UDP port where SNMP messages are received.

sysContact: Value of RFC 1213 sysContact.

sysName: Value of RFC 1213 sysName.

sysLocation: Value of RFC 1213 sysLocation.

Enable SNMP v2: Activates SNMP v2.

Because of security issues, it is advisable to use only SNMP v3, and to disable

SNMP v2. Accesses to SNMP v2 are always insecure.

Community public: The community password for SNMP GET requests.

Community private: The community password for SNMP SET requests.

Enable SNMP v3: Activates SNMP v3.

SNMP v3 Username: The SNMP v3 User Name.

Summary of Contents for Expert Net Control 2304
























































































Search results

Summary of Contents for Expert Net Control 2304

Reviews:

Related manuals for Expert Net Control 2304

Brands by name

Popular brands

Gude Expert Net Control 2304, Manual

Search results

Summary of Contents for Expert Net Control 2304

Reviews:

Related manuals for Expert Net Control 2304

Brands by name

Popular brands