background image

E-8

E-9

REPLACING THE UV-C BULB

TROUBLE SHOOTING GUIDE

Water vapor and humidity 

are not produced.

Power Plug: Unplug and then try again.

Power Failure: When the power is returned, try again.

Tank Installation: Make sure the tank is correctly attached.

The surface of the ultrasonic disk is dirty: Clean ultrasonic disk. (see pg. E-7)

PROBLEM

SOLUTION

Air blows but water vapor 

is not produced.

Excessive Water: Remove a certain amount of water from the tank. 

Increase mist setting.

Detergent residue and/or oil ingredients from cosmetics may be in tank; 

wash out tank and try again.

The surface of the ultrasonic disk is dirty: Clean ultrasonic disk. 

(see pg. E-7) If you use hard water, replace with softer water.

Humidity level is low.

The surface of the ultrasonic disk is dirty: Clean ultrasonic disk. (see pg. E-7) 

The water in the unit is too cold: Replace with cool, but not cold water. 

Damage on the ultrasonic disk: Contact Customer Service

The humidity has 

a bad smell.

Poor maintenance or dirty water: Clean the product thoroughly, 

and fill it with fresh water.

White dust is forming on

nearby furniture.

Hard water may deposit a certain amount of dust. Dust in the air also 

settles because of added humidity in the room. Use distilled water if 

this becomes a nuisance.

* Decalcification Filter (FLTDC) available at www.guardiantechnologies.com

  or through Customer Service 1.866.603.5900.

Unit has stopped working.

No or low water. Unplug unit and refill tank. Check timer has not been set.

Water is accumulating outside 

of unit or area surrounding unit.

Saturation of humidity. Lower mist control setting.

Unit not level and water is accumulating. Unplug and place on level 

surface. Point spray away from objects. Raise unit on a water-resistant 

level surface 2-3 feet off of floor.

Increased noise level.

Unit must be placed on a flat, level, hard surface. 

Make sure it is NOT placed on a soft or absorbent surface.

Warm humidity is not produced. It may take 10-15 minutes before warm humidity is created. The mist

may not feel warm due to the fact it is so fine and is cooled rather

quickly from the air in your home. Test by either feeling the base of the

unit which should be warm to the touch or by allowing the unit to run for

approximately 30 minutes on warm setting in a closed 200 sq. foot room

or smaller. The room should feel moderately warmer if the unit is

working properly.

Unit shuts off unexpectedly or 

does not operate.

Check that the safety device triggered. To restart, unplug for 5 sec/replug

then press the power button. Call Customer Service.

Water dripping when refilling.

Water remaining on bottom of tank. Wipe tank or tilt to drain before

transporting.

Make sure tank cap is secured tightly.

1. 

Unplug the unit.

2. 

Remove the tank and empty all water

  from the unit base and tank.

3.

 Flip the base over and locate the 

  UV-C Bulb Compartment.

4.

 Remove the two screws using 

  a philips screw driver.

5.

 Remove the lid with connected UV-C Bulb.

6.

 Twist the light bulb to the left until you can remove it.

7.

 Replace with new bulb, insert and turn 

  to the right to secure into place.

8.

 Replace the lid and secure with two screws.

Summary of Contents for H5450
















Reviews: