background image

iv

  GPX-SL25 Instruction Manual  

rev 03.21.13

Thank you for purchasing a GTO/ACCESS SYSTEMS GPX-SL25. When correctly installed and 

properly used, your GPX-SL25 operator will give you many years of reliable service. Please read 

the following information to ensure you have the correct system for your particular needs. This 

manual will enable you to properly install your GPX-SL25 Automatic Gate Operator.  
The GPX-SL25 operator is designed for installation on a slide-to-open single leaf gate. The 

gate must not exceed 24 feet in length nor weigh more than 650 pounds (please see Technical 

Specifications on page 2). The GPX-SL25 operator can be used on vinyl, aluminum, chain link and 

wrought iron gates. 
The GPX-SL25 operator accommodates extra transmitters, digital keypads, solar panels, push 

buttons, and other access control products. 

These optional accessories are noted with the

    

symbol

.

The GPX-SL25 operator features 

adjustable stall force

. This safety feature makes the gate stop 

and reverse direction within two seconds when it comes in contact with an obstruction.  The “MIN” 

setting means the gate will exert the minimum force on an obstruction before it stops and reverses 

direction.
The GPX-SL25 operator also has an 

adjustable auto-close 

feature. It can be set to remain open 

from 3 to 120 seconds before automatically closing. Pressing the transmitter button at any time 

after the gate fully opens will cause it to close immediately. “OFF” is the factory setting; meaning 

the gate will stay open until you press the transmitter button (or keypad, etc.) again.
Please call GTO at (800) 543-GATE [4283] or (850) 575-0176 for more information about our  

GTO/ACCESS SYSTEMS professional line of gate operators and accessories. Our Sales 

Department will be glad to give you the name and phone number of a GTO/ACCESS SYSTEMS 

dealer near you.

BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPERATOR:

Read these instructions carefully and completely to become familiar with all parts and 

installation steps. You must read the installation manual for detailed instructions on gate 

operator safety and proper use of the gate operator.

24/7 Troubleshooting Wizard: http://support.gtoinc.com

PLEASE READ THIS FIRST

, LLC

®

GTO Accessories are noted with this symbol in this Installation 

Manual. Information about accessories can be found on page 29.  

Summary of Contents for GPX-SL25









































Reviews: