GTO GPX-SL25 Installation Manual Download

Page: 39 / 40

GPX-SL25 Instruction Manual

rev 03.21.13

ADDITIONAL ACCESSORIES

Photo Beams

[R4222]

Primary “through beam” photo beam device. Provides “non-contact” entrapment

protection.

Push Button Control

[RB101]

Wire this unlit push button directly to your gate operator for simple open/close/stop

operation from up to 1000 ft. away. Use 16 gauge low-voltage wire.

Replacement Transformer

[RB570]

Standard 18 volt, 2200 mA AC transformer included with the GPX-SL25 to maintain

battery charge.

#41 Slide Gate Chain (R4487)

The #41 chain (25’ only) is used with the GPX-SL25 / GPX-SL252 DC Slide Gate Operators.

Post Mount Adapter Plate (R4983), (R4983 - 48) and (R4983 - 60)

Galvanized post mount adapter is availible in 30, 48 and 60 inches in length.

Pad Mount Adapter Plate (R4984)

Galvanized adjustable pad mount adapter for the GPX-SL25.

Summary of Contents for GPX-SL25









































Search results

Summary of Contents for GPX-SL25

Reviews:

Related manuals for GPX-SL25

Brands by name

Popular brands

GTO GPX-SL25, Installation Manual

Search results

Summary of Contents for GPX-SL25

Reviews:

Related manuals for GPX-SL25

Brands by name

Popular brands