GTO GP-SL100 Owner'S Manual Download Page 8

Page: 8 / 36

Important Safety Instructions

Install Screen Guard Over Gate and Fence

Injuries may occur when people put their hands, arms, legs, etc., through openings in the grill when the gate is

operated, trapping them between the grill and the fence post (or fence). All openings of a horizontal slide gate

must be guarded or screened to prevent a 21/4” diameter sphere from passing through openings anywhere in

the gate. This screen/guard must also be installed over the portion of adjacent fence that the gate covers in the

open position. Screening will prevent access through openings in areas where the gate travels.

Safety Edge

Screen Mesh

Safety Edge

Roller guard to prevent

pinch point hazard.

Roller guard to prevent

pinch point hazard.

Safety Edge

Required Safety Precautions for Gates

Safety Edge

Warning Sign Safety Edge

Roller Guard

Photo Beam

Pedestrian Gate

Moving Gate Can Cause

Injury Or Death

WARNING

Vehicle Gate

Operator

Roller Guards

Injuries occur when

hands become caught

between the gate and the

roller. Roller guards and

enclosed tracks must be

installed to prevent this

pinch point hazard.

Warning Signs

The warning signs (with orange panel) must

be installed on both sides of the gate.

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or

play in gate area.

3. This gate is for vehicles only. Pedestrians

must use a separate entrance.

Moving Gate Can Cause

Injury Or Death

WARNING

Entrapment Protection

GTO’s internal obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily

injury. For this reason, safety devices such as safety edges and photo beams MUST be installed. Furthermore,

a walk-through gate must be installed if pedestrian traffic is expected near the gate. We recommend the GTO

Bulldog Pedestrian Gate Lock (available as an accessory) for controlled access.

Summary of Contents for GP-SL100





































Search results

Summary of Contents for GP-SL100

Reviews:

Brands by name

Popular brands

GTO GP-SL100, Owner'S Manual

Search results

Summary of Contents for GP-SL100

Reviews:

Brands by name

Popular brands