manualshive.com logo in svg

GTO GP-SL100, Owner'S Manual

Share
Download
GTO GP-SL100 Owner'S Manual Download Page 15

12

Allen Bolts

with 5mm key

Washers

Mounting the Operator

1.

     Lift the operator and align its mounting holes over the 3/8” diameter concrete mounting anchors.

2.

     Lower the operator into position and fasten it to the mounting anchors with (4) 3/8” washers and

 

   nuts (not provided).

1.

     Turn the breaker power switch off before connecting AC power. Have a licensed electrician

 

   run 115 Vac wiring into the Field Wiring Connection Compartment. The 115 Vac line will power

 

   the gate operator system. The circuit must be protected with a 15 A main disconnect breaker    

   (not provided).

NOTE:  

Power and wiring connections MUST be

performed by a licensed electrician in accordance

with NEC (National Electric Code) and local codes.

NEVER

 

run low voltage (e.g., accessory or receiver)

wires in conduit containing 115 Vac wiring.

Removing the Operator Housing

Before you can gain access to the operator frame and its mounting holes, the housing will have to be

removed from the operator.

 

1.

     Remove the (2) 3/8” allen bolts and (2) m8 washers from the operator housing (this hardware is  

   located on each side of the housing).

2.

     Lift the housing off the operator and set it aside.

Connecting Power to the Operator

Summary of Contents for GP-SL100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands