manualshive.com logo in svg

GTO GP-SL100, Owner'S Manual

Share
Download
GTO GP-SL100 Owner'S Manual Download Page 3

Table of Contents

Gate Operator Class Categories

 ......................................................................................

Inside Cover

Metric Conversion Chart

 ..........................................................................................................................

Inside Cover

Safety Instructions for the GP-SL100  Slide Gate Operators

 .......................................................1

Important Safety Instructions for the System Designer

.....................................................................................1

Important Safety Instructions for the Installer

 ......................................................................................................2

Important Safety Instructions Specific to Secondary Means of Protection Against Entrapment

 .......3

Important Safety Instructions for the Consumer/End User

 ..............................................................................4

Required Safety Precautions for Gates

 .....................................................................................................................5

Warning Labels  ................................................................................................................................................................6

Technical Specifications  ..........................................................................................................................7

Parts Identification

 .....................................................................................................................................8

Installing the Gate Operator

 ...................................................................................................................9

Preparation of the Gate ..................................................................................................................................................9

Operator Installation Overview

 ..................................................................................................................................9

Using the Mounting Template  

 ............................................................................................................................... 10

Mounting Template (not to scale)  

 ......................................................................................................................... 11

Removing the Operator Housing  

 .......................................................................................................................... 12

Mounting the Operator  

 ............................................................................................................................................ 12

Connecting Power to the Operator  

 ...................................................................................................................... 12

Installing the Chain  

 .................................................................................................................................................... 14

Control Board Description

 ......................................................................................................................................... 15

Setting The Limits ......................................................................................................................................................... 16
Stall Force and Auto-Close Adjustments .............................................................................................................. 17

DIP Switch Settings

 ...................................................................................................................................................... 18

Input Connections

 ........................................................................................................................................................ 19

Accessory Terminal Connections ............................................................................................................................. 20

Output Connections

 .................................................................................................................................................... 21

Accessory Power Supply ............................................................................................................................................. 22

Prison Mode Operation and Wiring A 3-Button Station

 .................................................................................. 23

Reinstalling the Operator Housing

 ......................................................................................................................... 24

Installing a Dual System

 .........................................................................................................................25

Dual Gate Link Connection

 ........................................................................................................................................ 25

Setting Dual Gate Sequence

 ................................................................................................................26

Overview of a Dual Gate Operator Installation

 .............................................................................27

Maintenance

 ..............................................................................................................................................28

Troubleshooting Guide ..........................................................................................................................29

Warranty and Repair Service 

 ...............................................................................................................32

Installation Checklist

 ............................................................................................................. Back Cover

Summary of Contents for GP-SL100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands